Phone answered 24/7 · Frederick, MD and nearby communities

Call 24/7: (301) 804-1451
Carroll Creek Water ResponseWater Damage Help · Frederick, MD

Why Does My Sump Pump Run Constantly?

Last updated October 31, 2026

The short answer

Check the Float Switch

The float switch is the most common reason a sump pump runs nonstop. If the float gets stuck against the side of the pit or tangled in the pump cord, it can stay in the on position even when the water level drops. Lift the lid and watch the float as the pump runs.

You can gently move the float by hand to see if it falls freely. If it sticks, debris or a misaligned rod may be the cause. Clean the pit and adjust the float so it moves without catching. If the switch still sticks, the pump may need a replacement part.

Inspect the Check Valve

The check valve sits on the discharge pipe above the pump. Its job is to keep water from flowing back into the pit after the pump shuts off. If the valve fails, water rushes back, and the pump turns on again, creating a constant cycle.

Listen for a thud or a gurgle after the pump stops. That noise often means backflow. To test, lift the valve and see if water pours back. A faulty check valve is a simple fix, but if you are unsure, a local water damage pro can replace it safely.

  • Look for a valve with an arrow showing flow direction
  • Check for cracks or a loose fitting on the pipe
  • Listen for a thud right after the pump shuts off
  • Feel the pipe for vibrations that suggest backflow
  • Replace the valve if it shows any wear

Look for High Groundwater

Heavy rain or melting snow can raise the water table around your home. In a humid continental climate with cold snowy winters, spring thaw often brings a lot of water into the pit. If the pump runs for days after a storm, high groundwater is likely the cause.

You can check the water level in the pit. If it stays high even when the pump is off, groundwater is seeping in faster than the pump can handle. In that case, the pump may be undersized for the inflow, or the pit may be too small.

Test the Pump Size and Power

A pump that is too small for your pit will run constantly because it cannot keep up with the inflow. Compare the pump's motor strength to the pit depth and the volume of water entering. Most homes need a pump with at least one-third horsepower, but larger pits may require more.

Also verify the pump is getting full power. A weak electrical connection or a long extension cord can reduce performance. Plug the pump directly into a grounded outlet and test it. If the pump still lags, consider upgrading to a stronger model.

When to Call the Pros

If you have checked the float, valve, and water level and the pump still runs constantly, it is time to bring in local water damage pros. They can test the pump, check the discharge line for clogs, and inspect the pit for cracks or blockages. Their work usually involves a thorough evaluation of your drainage setup.

Constant running puts stress on the pump and can lead to failure, which risks water damage in your basement. Keep the shutoff valve location written down so you can stop the water quickly if needed. Act fast, because a failing pump can leave your home vulnerable to flooding.

  • A pro can test the pump's flow rate and compare it to the pit size
  • They can clear clogs in the discharge pipe that cause backpressure
  • They can check for cracks in the pit that let in extra water
  • They can recommend a replacement pump if the current one is undersized

Talk to someone now

Call (301) 804-1451 any time, day or night, and describe what happened.

Call Now (301) 804-1451

Frequently asked questions

How often should a sump pump run?

A sump pump should run only when water enters the pit. In dry weather, it may not run at all. After heavy rain, it might run every few minutes for a short cycle. If it runs constantly without stopping, something is wrong.

Can a stuck float switch cause the pump to run nonstop?

Yes, a stuck float switch is a leading cause. If the float gets caught in an upright position, the pump stays on even when the water level drops. Check the float for debris or a tangled cord, and move it by hand to see if it falls.

Is constant running a sign of a bigger water problem?

It can be. High groundwater, a cracked pit, or a broken discharge pipe can all cause constant running. If the pump works fine but the water keeps coming, you may have a drainage issue around your foundation. A pro can help identify the source.

Call Now (301) 804-1451